LME 21.130 C2
LME… replace the LMG automatic firing devices in the same housing… see table. With fault diagnostics.
| Manufacturer item no.: | LME 21.130 C2 |
| Type: | LME 21.130 C2 |
| Brand: | Siemens |
Related products
M5471 knitting stentering boarding machine
Product uses
This product is appropriate for polyester filament yarn, polyester low elasticity silk fabric, pure cotton or other knitting fabric with weight of 60-700g/m2.
Main technical index
Form: heated air circulation, single layer horizontal type
Vehicle category: left hand or right hand
Nominal width(mm): 1800-3600
Amplitude modulation range(mm): 700-(Nominal width-200 mm)
Speed range: 5-100m/min
Over-feed ratio: -10% - +30
Oasthouse temperautre: 100-230ºC
Heat source: heat-carrying oil, fuel gas(city gas, natural gas, water gas, liquefied petroleum gas), electricity
Cloth holding method: needle clamp
Cropping form: simple pendulum type; or double use
Edge detecting form: High precision infrared edge detecting
Guide rail form: no lubricating oil steel plate guide rail
Size: (16115+n×3000)×(W+2500)mm×2300mm
Installed capacity: (55+n×15)kW
Features
1. Active infrared, synchronous with main engine;
2. E+L tension sensor controlled padder, realizing low tension and constant tension running;
3. E+L infrared edge detecting indstrument, excellent antijamming capability;
4. 6mm thick steel plate graphite guide rail, no need of refueling, long serve life;
5. 9 section width adjustment;
6. Heat-carrying oil heating method, high accuracy;
7. Front and back double multistage operation system, PLC control system, convenient for operation;
8. Landing minor-cycle building block system oasthouse, small volume, large blast capacity;
9. Frequency converting control, high efficient heated air circulation system;
10. Special nozzle displacement;
CPB ( Cold Pad Batch) Machine
CPB ( Cold Pad Batch) Machine
Diesel / Heavy Oil Boiler
Diesel / Heavy Oil Boiler
Yuanda Boiler since 1956
Oil fired boiler is the 3-pass wet back boiler, can produce steam or hot water. This type boilers are fully automatic, safe, energy saving and designed to operate on a wide range of liquid and gaseous fuels like heavy oil, light oil, gas, and dual fuel options.
Output: steam
Capacity: 0.5-40 ton/h, 15hp-2500hp
Styles: horizontal
Available Fuel: heavy oil, diesel, furnace oil, waste oil, dual fuel, etc
Applied Industries: food, beverage, diaries, feed mill, garment, textile mill, paper mill, packaged, refinery, chemical, laundry, hotel, greenhouse etc
Vacuum Hot Water Boiler
Vacuum Hot Water Boiler
Boiler with oil/gas burner | Central heating boiler | Boiler for heating
Vacuum hot water boilers also named vacuum phase change hot water boiler. There is a vacuum condition inside, fill heat medium water in furnace and heat these water through oil/gas. Through heat exchange, the heat inside the boiler is transfered to outside water.
Transfer medium: hot water
Thermal Capacity: 0.3-7 mw 300-7,000 kw/h 200,000-6,000,000 Kcal/h
Efficiency: 99.9%
Available Fuel: heavy oil, diesel, furnace oil, biogas, NG, CNG, LNG, LPG, dual fuel
Applied Industries: heating & drying like: food, beverage, wood chamber, greenhouse, building heating, hotel, school, etc
STRIPPING MACHINE FOR ROTARY SCREENS
STRIPPING MACHINE FOR ROTARY SCREENS [ERALASER]
Description:
This machine has been designed to strip printing rotary screens;
Direct laser beam is used to strip (to remove) the coated resin from the nickel screen surface.
LASER STRIPPING MACHINE , the machine is generally equipped for taking up screens of standard repeats of 640mm, 820mm, 914mm, 1018mm. Screen lenght upto 3700mm.
Characteristics:
PLC Control ; Touch-Screen; Single Beam Laser; Long Life Laser Source.
The word Laser is actually an acronym
LASER
L is for Light
A is for Amplification
S is for Stimulated
E is for Emission
R is for Radiation
LASER ENGRAVING [LS100]
LASER ENGRAVING [LS100]
Description:
LASER ENGRAVING MACHINE LSC100 激光雕刻机
ENGRAVING MACHINE SUITABLE FOR RUBBER ROLLER AND RUBBER SLEEVES.
Laser engraving machine type LSC120
The laser engraving machine has two main parts: a laser source and a controller system. The beam emitted from the laser allows the controller to trace patterns onto the surface of the roller. The controller (computer) controls the direction, intensity, speed of movement, and spread of the laser beam aimed at the surface. The point where the laser beam touches the surface of the roller should be on the focal plane of the laser’s optical system, and is usually synonymous with its focal point. This point is typically small, less than a fraction of a millimeter (depending on the optical wavelength). Only the area inside this focal point is significantly affected when the laser beam passes over the surface. The energy delivered by the laser changes the surface of the material under the focal point. This is how material is removed from the surface to create an engraving. The surface material is vaporized during laser engraving, ventilation through the use of blowers and a vacuum pump that are required to remove the fumes arising from this process, and for removal of debris on the surface to allow the laser to continue engraving. The speed at which the beam moves across the material is also considered in creating engraving patterns. Changing the intensity and spread of the beam allows more flexibility in the design. For example, by changing the proportion of time (known as “duty-cycle”) the laser is turned on during each pulse, the power delivered to the engraving surface can be controlled appropriately for the material.
Characteristics:
PLC Control, Touch-Screen;
The word Laser is actually an acronym
LASER
L is for Light
A is for Amplification
S is for Stimulated
E is for Emission
R is for Radiation
Reviews
There are no reviews yet.